Threadall Manufacturing - Rods and Studs

By: Threadall  09-12-2011
Keywords: Studs, Bar Stock

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

For studs that are not completely threaded, there are two types of studs: full-bodied studs, and undercut studs. Full-bodied studs have a shank equal to the major diameter of the thread. Undercut studs have a shank equal to the pitch diameter of the screw thread. Undercut studs are designed to better distribute axial stresses. In a full-bodied stud the stresses are greater in the threads than in the shank.

Undercut studs (Rolled Thread) are also stronger because the metal is "rolled" up to the major diameter, not removed. This does not disturb the grain of the steel. Full bodied studs (Cut Thread) are weaker because metal is removed to create the thread, disturbing the grain of the steel.

Undercut studs are only required in applications where the stud is exposed to fatigue.*

Threadall Manufacturing Capabilities include


*Roll Thread and Cut Thread on Solids or Pipe

* From #2-56 to 4 ½" Diameter

* UNC, UNF and 8 Pitch

* Acme in both Full and Stub formats

* Metric and Contour Tylag (coil) Threads.

All Threads are available in Right and Left Hand .

* Special Pitches available.

* High Production Equipment for Threading Fully Threaded Studs,

* High Production Equipment for Double Ended Studs and Single

Ended Studs

- Lengths up to 20 feet for Roll Thread

- Lengths up to 40 feet or longer in Cut Thread depending on mill availability.


for additional information and pricing

Threadall Manufacturing Company - ISO 9001:2008 Certified

P: 1-877-777-2612 F: 519-576-3991


Keywords: Bar Stock, Studs,

Contact Threadall

Email - none provided

Print this page

Other products and services from Threadall


Threadall Manufacturing - Bolts

A screw is an externally threaded fastener capable of being inserted into holes in assembled parts, of mating with a preformed internal thread or forming its own thread, and of being tightened or released by torquing the head. A bolt is an externally threaded fastener designed for insertion through holes in assembled parts, and is normally intended to be tightened or released by torquing a nut. Round head bolts, track bolts, plow bolts..


Threadall Manufacturing - Heading and Bending

Bending is a manufacturing process that produces a V-shape, U-shape, or channel shape along a straight axis in ductile materials. Cold forming techniques are usually classified into four major groups: squeezing, bending, drawing, and shearing. Examples of applications include the heading of bolts and cap screws and the finishing of cold rolled steel*. Threadall Manufacturing Heading Capabilities Include. Long Lengths and Special Heads.


Threadall Manufacturing - Washers and Plates

Other uses are as a spacer, spring (belleville washer, wave washer), wear pad, preload indicating device, locking device, and to reduce vibration. A washer is a thin plate with a hole that is normally used to distribute the load of a threaded fastener, such as a screw or nut. Washers usually have an outer diameter about twice the length of their inner diameter.. Threadall Manufacturing Company - ISO 9001:2008 Certified.


Threadall Manufacturing - Nuts

The most common shape is hexagonal, for similar reasons as the bolt head - 6 sides give a good granularity of angles for a tool to approach from, but more corners would be vulnerable to being rounded off. The two partners are kept together by a combination of their threads' friction, a slight stretch of the bolt, and compression of the parts. Nuts are almost always used opposite a mating bolt to fasten a stack of parts together.


Threadall Manufacturing - Thread Rolling / Thread Cutting

Rolled threads are stronger than cut threads, with increases of 10% to 20% in tensile strength and possibly more in fatigue resistance and wear resistance. Threads of metal fasteners are usually created on a thread rolling machine. Threading capabilities at Threadall Manufacturing Include. They may also be cut with a lathe, tap or die.