The Firminator - Food Plot Tools - Firmiseeder - Food Plot Seed Driller - Deer Food Plot Implements
Seeds, tractor, Cultipacker
| || || || || || || |
| || || || || || || |
| || || || |
| || || |
6' Firminator G-3 - $8495.00
This is our most popular model to be used with your tractor. It requires a 30-horse power or larger tractor. This unit has a 3" square tube frame and weighs approx. 1450 lbs. It has category one and category two connection for your tractor. It includes adjustable disk angles, which allows you to change from zero degrees (or straight disks) to 5, 10, 15, 20 degree settings. It also comes standard with culti-packer mud scrapers, disc mud scrapers, and center ripper shank. There are 12"-18" disk blades on the six foot model and 30-9" diameter cultipacker wheels. Disking width is approx. 67" and the cultipacking width is 70".6' FirmiSeeder -$6995.00
This high demand implement is basically The Firminator without the disk components. It will enable those who already own tillage equipment the ability to accurately plant a wide variety of seed species and blends through the ground driven Accu-Seed metering system with the added benefit of the cultipacker to firm the seed bed prior to or after planting the seed. The FirmiSeeder can be modified by adding the disk components at a later time to complete The Firminator G-3 implement.16" Cultipacker Upgrade-$750.00
For those working on sandy soils or fine silty soils the larger cultipacker wheels can make a big difference. The larger wheel will easily roll over the loosest soils that tend to flow up and over the standard wheel. Both The Firminator G-3 and The FirmiSeeder models come standard with 30 of the original 9" diameter by 2-1/4" wide wheels. The larger wheels are 4" wide, and there are 17 on each six foot unit. Note* The upgrade to the 16" wheels adds approximately 225 pounds to the unit for a total weight of 1700 lbs.Seed Box Agitator - 6' $535.00
This is an up-grade option available for both the Firminator and FirmiSeeder. This shaft is installed in the bottom of the seed box and is driven off of the sprocket drive assembly that turns the Accu-Seed metering system. The agitator shaft is useful for keeping custom seed blends containing extremely small and large seeds together evenly blended. This prevents the smaller seeds from flowing too quickly through the metering system, since it needs to be opened large enough to accommodate the largest seed in the blend. Note* if you are using pre-packaged seed blends you likely will not need the agitator.Hydraulic Top-Link Cylinder
Category-one cylinder with 3/4" pin holes - $375.00
Category-two cylinder with 1" pin holes - $444.00
This is another up-grade option for The Firminator G-3 and The FirmiSeeder. We supply a hydraulic cylinder with the appropriate connections for your tractor that replaces the standard manual "turn-buckle" top-link. This allows you to adjust The Firminator's forward or rearward tilt from your tractor seat, by operating the auxiliary hydraulic control lever. Of course your tractor must first have an auxiliary hydraulic connection. When ordering, please specify tractor make, model, horsepower, and category one or two three point.
To ensure the proper length cylinder, please measure your tractors top link from eye to eye at the shortest (closed) position. This length is vital for us to provide the proper cylinder for your application.
Pictured at top is our category-one cylinder. It has 3/4" pin holes and will include the hydraulic hoses and appropriate end fittings. (Not shown) $375.00 complete with cylinder, hoses, and fittings.
Pictured at bottom is our category-two cylinder. It has 1" pin holes and includes the hydraulic hoses and appropriate end fittings. (Not shown) $444.00 complete with cylinder, hoses, and fittings.
| || |
| || || || || |
| || || ||
|| || || |
| || || || || |
The information in this article was current at 06 Dec 2011