services

By: Purpledish  09-12-2011
Keywords: Cards, Satellite TV, Smart Cards

Dish network satellite tv hacking DSS dishes descramblers, DSS dish hacking converter boxes, smart cards alterations, dish cable hacking, test chips, hu card bev keys dish keys dish idea, bev idea, p4 hack, hu hack, atmega cards


 What are private files/scripts? FTA receivers are able to be simply programmed using our software enabling you to alter/modify the receiver's capabilities. We sell access to our private files section on a monthly basis (click here to view).

The receivers have no cards so you are not hacking anything, simply put you are changing the file structure of the mother board in your receiver. This process can easily be reversed and set to factory settings at will if you no longer wish to have all Dish Nework channels and prefer the free to air channels.

Why purchase from us? Purchase 3 months of script support for your FTA or any Dish Network receiver. No programming skills needed, we supply the software and files to keep you watching your favorite channels.

Why do we offer 3 months support? Well the answer is easy.

Our files are meant to last. Our in house programmers create all the files for your individual needs.

So in reality you are paying $8/month for total access.

If you watch 2 pay-per-view movies (rented cost of $5.00 at Block buster) you've just paid for your membership and profited $2 each month. JTAG products are based on IEEE 1149.1 standard from the Institute of Electrical and Electronics Engineers (IEEE) and allow for boundary scan-testing on printed circuit boards PCBs), or on blocks of components on an integrated circuit (IC). JTAG products are also known as boundary scan products.

JTAG products include devices such as cables and readers. These JTAG technologies include a JTAG cable, which is often used to program devices that have internal flash memory. A JTAG receiver is a receiver that has a JTAG port, common in satellite dish networks applications. A JTAG product is frequently used on satellite dishes and involves plugging a reader into the JTAG port on the dish to troubleshoot certain problems with the system’s embedded software.

After reading this simple, easy to follow guide, and following all the instructions exactly, you will be able to extract your receiver's box keys and dump your TSOP.

The box key is useful when using camless solutions such as emulation or when using the Atmega. Dumping your TSOP is a good idea because there is always the possibility of an ECM that targets your TSOP. Almost anyone with experience will tell you it is a good idea to dump your TSOP.

This guide will assume you have some basic knowledge and know how to download files off the internet and unzip them. Please note we take no responsibility for any damage you may cause as well as any laws you may be breaking. Please read the disclaimer on the home page. This guide is for educational purposes only. Enjoy. Difficulty Level The difficulty level of this project is 7 on a scale of 1 to 10. It will require that you solder wires to the bottom of your receiver and you must have at least a little bit of experience with soldering in smaller areas. This project should take you 45 minutes if all goes well. What's Needed Jkeys 1.33 Dish Network IRD must have JTAG port on bottom The following models have JTAG: 2700, 2800, 3700, 3800, 3900, 4700, 4900, DP301 (3100), PVR501 (5100), 6000 plus DRD420, 440, 480 Computer: must have available printer port 5 100Ohm Resistors I've heard that 1/8 to 1/2 Watt will work, I know 1/4 Watt works Soldering Iron 25 Watts or so Wire Cat 5 works best, but regular copper wire works too you wont need too much wire. You will need 6 pieces that are 6 inches or so Solder any 60/40 solder DB 25 Connector you will want a male connector because your computer's printer port in female.

Building the JTAG The first thing you're going to do is make the simple JTAG reader. First, solder the 5 100 Ohm resistors to pins 2, 3, 4, 5 and 13 . Now, take your 5 pieces of 6 inch wire and solder one each to each end of the 5 resistors. You may not get proper results if your wire is longer than 6 inches. Now would be a good time to inspect all your solder joints and make sure that you didn't leave a solder spike across any of the pins. Now, you must make a connection for ground. This is done by taking the last wire you have and soldering it to pins 18-25 of the DB 25.

Hooking up the JTAG Once you have the JTAG reader built, you now want to solder it to your IRD. First of all, you should pre solder your wires. Just add a little bid of solder to the end of each wire.

***Please note that if you aren't careful when soldering your JTAG to your IRD, you can mess something up. Please note that I take no responsibility for whatever may happen. Many people say that you shouldn't solder at all to those pads on the bottom of your IRD. I have done this on 4 different IRDs and never had a problem, but that doesn't mean you wont. BE CAREFUL AND DON'T CROSS ANY WIRES. You've been warned!***

Ok, once you've pre soldered your wires, you now have to figure out where you are going to solder your wires to on the bottom of your IRD. Make sure your IRD is unplugged when soldering to it. As a reference: 2700, 2800, 3700, 3800, 3900, 4700 & 4900 IRDs 3100 IRD 5100 IRD 6000 IRD. Please note where the front and back of the IRD is. Make sure that you have good connections to the proper pads. DON'T HOLD THE SOLDERING IRON ON THE PADS TOO LONG. I don't even like to touch the IRD pads. What I do is hold the soldering iron to the wire and let the heat melt the solder that is on the wire when I pre soldered it. Inspect all your joints and make sure that there are no crosses and that your JTAG wires aren't touching each other.

Getting your Box key You now want to download Jkeys and unzip it to a folder of your choice. Connect your JTAG to your computer's printer port and plug in your IRD. DO NOT TURN THE IRD ON. Just plug it in. When you start Jkeys, your box keys should be there. If you don't see your Box key and IRD number, make sure that all your connections are good and no wires are crossing. ONCE YOU HAVE YOUR BOX KEY, WRITE IT DOWN IN A SAFE PLACE! YOU DON'T WANT TO LOSE THIS! . It might be a good idea now to save your TSOP in case of an ECM. No one would argue that it is a bad idea to have a back up of your TSOP on your computer. Read the next section for information on backing up your TSOP.

Backing up your TSOP Once you have got your box key, you should dump (make a back up) of your TSOP. Doing this is not to difficult with JKeys. All you have to do is look at the chart below, and then enter the values into JKeys. Different IRDs have different TSOPs, so that means they have different start addresses and sizes. To dump your TSOP, find your IRD in the chart below, then enter the values for your IRD into JKeys. Then press "Save Mem". Note that the 3100 and 5100 have two TSOPs, so you must save both!

The information in this article was current at 06 Dec 2011

Keywords: Cards, Dish Hacking, Dish Keys, Dish Network Satellite, Dish Network Satellite Tv, Network Satellite, Programming Skills, Satellite TV, Satellite Tv Hacking, Smart Cards,