Accessories

By: York Chutes  09-12-2011
Keywords: Door, Fire Damper

Accessories

Top Cap Assembly

Top Cap has a manually opened cover
to allow 100% smoke release and
rain shielded permanent venting equal
in area to the cross sectional area
of the chute. Fabricated with rust-proof hardware.

Tall Cone flashing & Storm collar
to be installed above the roof

D

24 1/8" (613 mm)

22 1/8" (562 mm)

20 1/8" (510 mm)

A

31" (787 mm)

29" (737 mm)

27" (686 mm)


Disinfecting & Sanitizing Unit

Flushing Spray Head

Supplied only when specified

The Disinfecting and Sanitizing Unit
is a tank with a capacity of approximately
4 litres, complete with dispensing
valve assembly, generally located above
the uppermost intake door,
which dispenses a concentrated
disinfectant fluid into the wash down
water, and has an on/off control
to permit rinsing as well.

Note:

a vacuum breaker must be installed by the plumbing trade when being hooked up. To allow refilling when required, an access door must be installed in the wall in line with the Sanitizing Unit.

Chute Riser & Anti-vibration Mounting

Chute Riser
Standard diameter 610 mm Aluminum,
Aluminized Steel, Satin Coat,
or Stainless Steel.
Beaded Slip Joint

Anti-vibration Mounting
Floor Frame and Fastener
Rubber Grommet
Neoprene Pad
Floor Slab


Spring Load Fire Damper

D

24 1/8" (613 mm)

22 1/8" (562 mm)

20 1/8" (510 mm)

A

26 3/4" (679 mm)

25 7/8" (657 mm)

22 3/4" (508 mm)

B

29 1/4" (740 mm)

29 3/4" (756 mm)

25 3/4" (655 mm)

The horizontal direct type accordion door is most commonly used when discharging directly into a compactor and/or container. The damper has a 1 1/2 hr. ULC label and is held open on a 74°C spring loaded fusible link assembly. This door is intended only to provide smoke and fire protection to the chute riser.

Keywords: Door, Fire Damper

Contact York Chutes

Email - none provided

Print this page

Other products and services from York Chutes

09-12-2011

Recycling Chutes

Welded steel construction throughout: door andframe in 11 Ga. YTR – York Tower Recycling intake door. Bottom hinged, hand operated door.


09-12-2011

Compactor/Container

Hi-Pak feature 3 hp electric motor c/w 4" bore hydraulic cylinder. Electrical motor 3/60 - 208/575.


09-12-2011

Garbage Chutes

37 lbs.Available sizes of YS model (Custom sizes available upon request. Welded steel construction throughout: door and frame in 11 Ga. Bottom hinged, hand operated door.


09-12-2011

Linen Chutes

Rise 60 min. 250°C.Warnock-Hersey tested to CAN4-S104, ASTM E-152 and NFPA-252. Brushed satin finish with silent self-closing, self-latching mechanism. Solidly welded stainless steel: 13 Ga door and frame. SS bottom hinge - garbage intake door also available. Hand operated door with 180° swing. Hour fire rated door with Temp.


09-12-2011

products

Side or bottom hinged doors in 13 Ga welded stainless steel construction with brushed satin finish. Manufactured in Canada to meet the strictest fire standards and current building codes. Chute risers in 16 or 18 Ga aluminum, aluminized steel, satin coat, or stainless steel. Chute support frame with anti-vibration mounting system at each floor. All doors are approved for drywall or masonry installation.


09-12-2011

services

Exhaust fans for garages, roofs and specific rooms such as laundry, elevator, garbage, pool, lockers, and much more. We use the latest plasma and laser for custom cutting and only the newest Auto-Cad software for precise results. Steel plates and platforms in garbage rooms, walkways and under container areas. Manufacturer of high-rise garbage compactors and Bi- or Tri-sorter systems. Safety guards for wall-mounted access ladders and windows.