TenPlus Architectural - Products - Door Grilles

By: Tenplus Architectural  09-12-2011

The Ventex door grille, by TEN Plus Architectural, incorporates an inverted, rounded “Y” blade. This blade design maximizes available free area. Also, this sight proof design provides exceptional strength and protection against vandalism.


Recommended Specification for
Door Grilles

Supply and install Ventex stationary door grille model DG, by TEN Plus Architectural. The door grille shall be adjustable in depth from
a minimum of 1 3⁄4” (44.5 mm) to a maximum depth of 2 3⁄4” (70 mm). Blades shall be 0.060” (1.52 mm) and frame shall be 0.060” (1.52 mm) extruded aluminum, alloy 6063-T5.

The door grille shall have a standard clear anodized finish (or other specified finish).


Contact Tenplus Architectural

Email

Print this page

Other products and services from Tenplus Architectural

09-12-2011

TenPlus Architectural - Products Louvers Model2630-CLD

All materials shall be factory finished after assembly with Polyester Baking Enamel in a color selected from the Ventex Color Chart. The Ventex model 2630-CLD, by Ten Plus Architectural provides a front fixed drainable blade, with a rear operating blade. This designmaintains a uniform external appearance, while allowing for air flow control. The drainable front blade helps in reducing water entry. Recommended Specification for Model 2630-CLD.


09-12-2011

TenPlus Architectural - Products Model 2620/2625

The louver manufacturer shall submit test data on a 48” x 48” unit showing that the louver conforms to the data on this page.OTHER MODELS IN THIS SERIES. All materials shall be factory finished after assembly with Polyester Baking Enamel in a color selected from the Ventex Color Chart. The Ventex model 2620/2625, by TEN Plus Architectural, is the extruded aluminum, stationary, six-inch deep stormproof louver.


09-12-2011

TenPlus Architectural - Products ACL600/605, ACL800/805, ACL1200/1205

Louvers shall have a 19 gauge galvanized birdscreen.All materials shall be factory finished after assembly with Polyester Baking Enamel in a color selected from the Ventex Color Chart. Supply and install stationary louvers Model ACL600 / ACL605, Model ACL800 / ACL805 or Model ACL1200 / ACL1205, by TEN Plus Architectural. Blades and frame shall be 0.063” formed aluminum, or 0.095” 6063-T5 extruded aluminum.


09-12-2011

TenPlus Architectural - Products - BrickVent Louvers Model BV

All materials shall be factory finished after assembly with Polyester Baking Enamel in a color selected from the Ventex Color Chart. The brick vent features both extended head and extended sill to provide a drip edge for water to travel around the opening. The Ventex model BV, by TEN Plus Architectural, is a heavy-duty extruded aluminum brick vent. Opposed blade damper that can be opened through the face.


09-12-2011

TenPlus Architectural - Products Model 2210/2215

The S2302 is normally used as an exhaust louver, for applications where the total CFM is relatively low or the louver height is restricted. All materials shall be factory finished after assembly with Polyester Baking Enamel in a color selected from the Color Chart. The S2302, by TEN Plus Architectural, is a two inch deep, straight blade exhaust louver, with a high free area.


09-12-2011

TenPlus Architectural - Products Model 2410/2425

The S4352, by TEN Plus Architectural, is a four inch deep extruded aluminum, stationary exhaust louver.The S4352 design provides an extremely high free area. The benefit of this is that the louver can exhaust a high volume of air with little static pressure. Supply and install stationary louver models S4352.