Roofing, Underlayment, moisture, barrier, metal roof, tile roof, shingle - msds

By: Roofaquaguard  09-12-2011
Keywords: Roofing, Roof Deck, Roofing Underlayment

Material Safety Data Sheet (MSDS)

1. Product identification, composition and use
Product Name: RoofAquaGuard UDLX
Composition: RoofAquaGuard UDLX is a 5-ply, 100% asphalt and
asbestos free. RoofAquaGuard UDL is a base sheet made
of woven Polypropylene laminated on the bottom side with
a high “cof” (Coefficient of Friction), modified Ethylene based coating. The top side is extrusion laminated to a polyester non-woven
Product Use: Intended for use as a roofing underlayment
Manufacturer:

Nordic Waterproofing Oy

Puusepantie 11
04361 Tuusula
Finland

Telephone: 011 358 9 870 441
Fax: 011 358 98251 070

2. Hazardous Ingredients/Warnings
The product is chemically inactive and is biologically inert. It is not a skin irritant.
RoofAquaGuard UDLX underlayment raw materials and additives contain no asbestos or asphalt products.

This declaration is based on individual approvals obtained by the suppliers of raw materials and ingredients.

To avoid danger or suffocation, the product should be kept away from babies and children. This product is not considered dangerous to the environment.

3. Fire Hazard
This product burns, but is not classified as flammable. Flash point is approximately 350° Celsius (662° F).

The final products at complete combustion are carbon dioxide and water. At incomplete combustion with reduced oxygen supply, carbon monoxide, which is highly toxic, may form.

As for many other compounds, like wood, paper and other products from oil other decomposition products like various hydrocarbons, acids and aldehydes may also form, but only in very small quantities.

4. Fire Fighting
Water in a spread jet, dry chemical, foam and carbon dioxide can be used.

5. Handling
The product is stable under normal conditions of use, storage and transportation. For safe installation, it is recommended to follow installation instructions given by the manufacturer/seller.

6. Waste Handling
The product can be used as landfill, or incinerated, as required.

DISCLAIMER
THIS INFORMATION IS FURNISHED WITHOUT WARRANTY EXPRESSED OR IMPLIED, EXCEPT THAT IT IS ACCURATE TO THE BEST KNOWLEDGE OF Nordic Waterproofing Oy AND ASSUMES NO LEGAL RESPONSIBILITY FOR USE OR RELIANCE ON THIS DATA

Specification Sheet

1. Classification
Roof covering and roof deck construction-Underlayment Can be used on steep sloped roofs beneath composite, metal, clay, concrete, slate, wood and other roofing materials.

2. Product Name
RoofAquaGuard UDLX High Performance Roofing Underlayment

3. Manufactured for
Nordic Waterproofing Oy

Puusepantie 11
04361 Tuusula

4. Product Description
RoofAquaGuard UDLX is a 5-ply, 100% asphalt and asbestos free, high
performance roofing underlayment used on steep sloped roofs beneath
composite, metal, clay, concrete, slate, wood and other roofing materials. RoofAquaGuard UDLX is a base sheet made of woven Polypropylene, laminated on the bottom side with a high “cof”, Modified Ethylene based coating.

The top side is extrusion laminated to a polyester non-woven.
RoofAquaGuard UDLX is approved as an alternate replacement for Type 15 or Type 30 asphalt roofing felt. RoofAquaGuard UDLX measures 60" wide and comes in 200' rolls weighing 40 lbs per roll. The coverage per roll is 9 1/4 squares. RoofAquaGuard UDLX is gray in color which helps reduce heat loads on attic structures.

5. Approvals
ICC-ESR
Miami Dade
Florida Building Code
CAN/CSA

6. Testing
ICC-ES AC 188 and ASTM D226 (passed)

Miami Dade (passed)
Florida Building Code (passed)
CAN/CSA: A220 (passed)

7. Installation
RoofAquaGuard UDLX must be installed above properly ventilated spaces (follow local building code) as it is considered a vapor barrier. RoofAquaGuard UDLX is laid horizontally (parallel) to the eave with the printed side up, and with 4" horizontal laps and 6" vertical laps. (The use of a slip sheet is not required underneath metal roofing)

RoofAquaGuard UDLX must be attached to the structural Roof Deck Material
using Plastic or Steel Cap roofing nails, having a minimum of 1" diameter cap, spaced at 12" on vertical and 15" on horizontal. All Plastic, or Steel Caps, must be attached flush with the underlayment surface and nails must be fastened at a 90 degree angle to the deck. Prior to loading the roofing materials onto the RoofAquaGuard UDLX product it is recommended that a roof jack, with planks, toe boards, or a strong platform be secured to the underlying roofing deck to prevent slippage of stored materials on steep sloped roofs (greater than 4 : 12 pitch). See OSHA regulations (Standard 29 CFR), fall protection systems criteria and practices - 1926.502. For batten secured applications, the use of plastic cap roofing nails required only to secure the underlayment and prevent blow off until the batten system is installed. Where seams or joints require sealant or adhesive, use only a high quality, low solvent asbestos free plastic roofing cement meeting ASTM D-4586 Type 1 (Asbestos Free), Spec SS-153 Type 1 (Asbestos Free). Installing final roofing within 6 months from initial underlayment application is recommended.

8. Technical Services
RoofAquaGuard UDLX provides a 35 year limited material warranty. For warranty and technical information, go to warranty page.

9. Maintenance
None when installed in accordance with manufacturer's recommendations.

Roof Aqua Guard North America Marketing and Sales: Nemco Industries Inc

Keywords: Roof Covering, Roof Deck, Roofing, Roofing Underlayment

Other products and services from Roofaquaguard

09-12-2011

Tile Synthetic Roof Underlayment, Metal Roofing Underlayment

This peel and stick product is specifically designed to cater for the growing Metal and Tile markets, but is also user friendly with other roof covering materials. 36.6" inch wide rolls with high quality 4" selvage edgeDecreases number of overlaps, speeds up installation by about and decreases possible water ingress.



09-12-2011

Roofing, Underlayment, moisture, barrier, metal roof, tile roof, shingle - manufacturer and warranty

THERE ARE NO WARRANTIES EITHER EXPRESSED OR IMPLIED, EITHER AT COMMON LAW OR BY STATUTE INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES UNDER THE SALE OF GOODS ACT C.410, AND THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH MODIFY THE WARRANTY CONTAINED IN THIS DOCUMENT.


09-12-2011

Synthetic Roof Underlayment, Metal Roofing Underlayment, Tile Roof

60 inch wide rolls, one of the widest Roofing Underlayment’s in the industryDecreases number of overlaps, speeds up installation by about 30% and decreases possible water ingress1,000 square feet per roll relates to only an average of 2 to 3 rolls per project.