Perchloric Acid « HHHawkins

By: H.h. Hawkins  09-12-2011
Keywords: Stainless Steel, Plumbing Fixtures, counter top

Perchloric Acid « HHHawkins


Perchloric Acid Fume Hood

The Perchloric Acid Fume Hood has the same general performance characteristics as the Balanced Air Fume Hood
with the additional feature of a coved seamless welded interior cavity using type 316 #4 finish stainless steel as
recommended by Insurance Underwriters. The interior cavity also has an integral full width drain trough to facilitate the
recommended frequent and thorough wash-downs. It is also recommended that the ductwork be made of a relatively
inert material such as stainless steel. Exhaust ductwork should be as short and as straight as possible. Perchloric
hoods must never be manifold into duct systems that serve any other type of fume hood or any other equipment.

Designed to be fixed directly to the base cabinets (no counter top needed)

  • Generous 261/2” interior depth
  • Tall front opening view height of 673/4” with standard 36” base cabinets
  • Vertical rising sash
  • Upper and lower by passes
  • Aerodynamic air foil with electrical cord access
  • Factory set interior baffles
  • Fluorescent lamp, light switch and two electrical outlets 120V/15A with internal wiring to a junction box
  • Front corner posts pre-punched to accept up to 10 plumbing fixtures
  • Removable exterior side panels
  • Stainless steel type 316 interior lining and counter top with coved seamless welds
  • Full width integral back trough
  • A 3/4” diameter P.V.C. spray pipe hookup to a remote controlled valve is provided for periodic wash down behind baffles

Keywords: Base Cabinets, Corner Posts, counter top, Electrical Cord, electrical outlets, Finish Stainless Steel, Fume Hood, Junction Box, Light Switch, Plumbing Fixtures, Side Panels, Stainless Steel,

Other products and services from H.h. Hawkins


Radio Isotope « HHHawkins

The fume chamber and integralwork surface consist of a welded seamless construction with all coved corners. The design of the radio-isotope fume hood provides a safe environment for working with Isotoperadiation. Stainless steel type 304 interior lining and counter top with coved seamless welds. Removable exterior side panels (no access panel inside the hood. Designed to be fixed directly to the base cabinets.


Fully Accessible « HHHawkins

The Fully Accessible Fume Hood has the general performance characteristics as the Balanced Air hoodwith the addition that all services are located at an accessible height for wheel chair operators. Astainless steel spill trough is located under the front portion of the hood to prevent any chemicalspillage. Front corner posts & interior side panels pre-punched to accept up to 10 plumbing fixtures.


Balance Air « HHHawkins

When the sash islowered, air is fed through the louvered top section as well as through the aerodynamic airfoil located underthe sash creating a sweeping air movement at the work surface to reduce dead-air pockets and airturbulence at the work surface front. With conventional hoods, face velocity becomes excessive when the sash isat a lower position, disturbing the work being conducted inside the hood.


Variable Air « HHHawkins

The Variable Air Volume fume hood combined with an HVAC control system is designed to vary the hood’sexhaust rate to maintain a constant average face velocity throughout the sash travel. Front corner posts & interior side panels pre-punched to accept up to 10 plumbing fixtures. Upper and lower by passes with interior adjustable top front cover. Aerodynamic air foil with electrical cord access.


Fume Hood « HHHawkins

This result in reduced operating costs in addition to lower first costs.With the Vanguard Fume Hood there is no need to work with restricted sash openings to reduce the amount of exhaust air, its performance numbers are achieved with a full open sash. Generous 26 1/2” interior working depth while maintaining an overall 32 3/4” exterior dimension. Interior lining components are available in non-metallic or stainless steel finishes.


Products « HHHawkins

The Vanguard Fume Hoods offer a combination of high performance, containment safety, energy efficiency and space utilization which will perfectly adapt to the realities of all modern laboratory environments. Choose from a complete line of floor mounted case Work, castered cabinets or under-counter suspended cabinets designed to work with all of ourAdaptable Furniture Systems.


Auxillary Air « HHHawkins

Ideally suited to labs with limited HVAC capacity, the Auxiliary Air Fume Hood controls air velocity in muchthe same way as the Balanced Air Hood. This auxiliary air is introduced outside the fumehood above the sash and enters the hood through the face with the sash open. In addition the Auxiliary Air Hood features an upper front intakeplenum to reduce the consumption of conditioned room air.