Positive Displacement Blowers / Products

By: Aerzen Canada  09-12-2011
Keywords: blower, Positive Displacement Blowers, Displacement Blowers

Key Features of an Aerzen Blower
  • - Reliable oil splash lubrication;
  • - Three lobe rotors;
  • - Heavy duty shaft;
  • - Helical timing gears;
  • - Heavy duty bearings;
  • - Multiple labyrinth sealing with vent chamber;

Our goal = Minimal life cycle cost in 24/7 and severe duty applications

Construction and design - Aerzen Positive Displacement Blowers
Are twin shaft rotary machines. The two rotors are placed axially parallel to each other and centered within the housing. Timing gears ensure that the rotors revolve without making contact. The rotors are supported on ball and roller bearings. In order to achieve a high efficiency the clearance between the rotors is kept to a minimum and is based on the pressure differential and thermal load expected under operating conditions. In case of larger blowers the roller bearing clearances and the shaft deflection have an influence on the clearance. Larger clearances between the rotors and the end plates compensate for axial thermal expansion at the floating bearing end.

The housings are made of high quality grey cast iron (GG 20). The blower housing requires no additional cooling, even at high loads. Up to the size GM 80L, the blower feet are bolted on.

Sealing configuration, series GL and GM

These models are designed to convey air or neutral gases. The conveying chamber is sealed from the oil chambers by means of an oil slinger in conjunction with piston ring labyrinth type seals featuring a generously dimensioned central vent chamber (condensate channel), and which plays a crucial role in ensuring that the medium conveyed remains clean and oil-free. The drive shaft is sealed by means of a radial seal ring installed in the housing cover.

Special designs possible at any time.


The rotors are dynamically balanced. Smaller blowers of the sizes GM 3 S - GM 80 L feature steel rotors and shafts (C 45 N), drop-forged in one single piece. Sizes GM 90 S and larger are constructed with pistons made of GGG 40 and steel shafts (C 45 N). Where contamination particles are likely to accumulate during operation, the cavities of the cast iron rotors are capped.

Timing gears

The helical timing gears are tempered, and then ground to an exacting degree of precision. The positioning and fastening of the gears onto the shafts takes place via taper interference fit, guaranteeing both excellent concentricity and reliable adherence.

Special materials

Non-standard materials such as nodular graphite cast iron (GGG 40), cast steel (GS - C 25) and CrNi - cast steel are available for special applications. Special requirements, however, must be clarified with the manufacturer in advance!


Our blower units normally include the standard accessories for continuous operation. The installation is effected on flat, load bearing surfaces, elevated floors or steel structures, a rigid installation on concrete foundations is also possible. In most cases the blowers are driven by a three-phase asynchronous motor and - for adjustment of the volume flow - a belt drive. Upon demand special designs as direct coupling, intermediate spur gear or special materials are also available.

Keywords: blower, Displacement Blowers, Positive Displacement Blowers,

Other products and services from Aerzen Canada



Suction throttle control:Since final compression temperature is governed by the injected oil, a greater range of compression ratios such as may arise when the induced volume is throttled down, can be safely coped with. Using this method, the surplus gas volume is allowed to flow back to the intake side by way of a governor that is controlled by the admissible final pressure.



Wherever air and gases of most various kinds are conveyed, compressed or measured twin-shaft Positive Displacement machines made by Aerzener are used.A wide range of Positive Displacement blowers and Screw compressors made by the Aerzener Maschinenfabrik is available for almost all the branches of the industry.


After Sales Service

From experience and professional understanding we offer you several proven preventive solutions: from maintaining your blowers, compressors or vacuum pumps, to extending your critical uptime to help in troubleshooting. A blower or compressor failure or problem may cause complete plant shutdown. Aerzen stocks blowers from 1 m3/min to 150 m3/min.