Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series PQ

By: Cvs Controls  09-12-2011

CONTROL VALVES - Series 128PQC

The CVS Series 128PQC Control Valve body assemblies are suitable for on-off dump valve service in oil and gas production applications, in either sweet or sour gas conditions. These valves are also useful for on-off high-pressure control of numerous gasses and liquids, and can be used with materials that are viscous or erosive.

This is a single port valve with unbalanced stem-guided valve plug, and push- down-to-close valve plug action. Operated by a Type 128 spring-and-diaphragm actuator, the assembly can be operated in a normally open or normally closed application. This setting can be reversed in the field with minimum disruption and no additional parts.

CVS Type 128PQC is a 1-inch Control Valve, standard configuration is with a solid pipe plug threaded into the bottom connection for straight-through flow. To convert the control valve to angle flow, the pipe plug can be installed in the left port.

Note: This configuration from straight-through flow to angle flow can be achieved in the field.

The CVS Series 128PQC valve is available with soft-seat, cageless soft seat, or all metal seat construction. All configurations have push-down-to-close valve plug action.

The valve plug shuts off against the integral seat ring in the cage, except in cageless soft-seat construction, where the shut-off is against the seat which is cut into the web of the valve body. Rotation of the valve plug is limited with the use of a nylon insert in the valve plug thread.


Other products and services from Cvs Controls

09-12-2011

Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series D

The CVS Series D and Series DA are single port, screwed-in, metal-seated globe style valve with unbalanced post-guided plug and push-down to close plug action used for high-pressure applications. CVS Controls manufactures Control Valves and associated instrumentation products to specification that facilitate the direct replacement with FISHER* process control equipment.


09-12-2011

Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series E

The flow direction for standard cages is flow down, and the flow direction for the CVS EZ is up through the seat ring with the following flow characteristics available: linear, quick opening, and equal percent. Design “CVS ET” is intended for applications requiring low leakage rates with composition seating for tight shutoff requirements or metal-to-metal seating for higher temperature capabilities.


09-12-2011

Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series EW

The flow direction for EWD and EWT is normally flow down, and the EWS is normally flow up with the following flow characteristics available: linear, quick opening, and equal percent. CVS Controls manufactures Control Valves and associated instrumentation products to specification that facilitate the direct replacement with FISHER* process control equipment.


09-12-2011

Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series H

CVS Controls manufactures Control Valves and associated instrumentation products to specification that facilitate the direct replacement with FISHER* process control equipment. Design “H5T” is a single port, globe-style body with cage guiding, balanced valve plug and composition or metal seats. Design “H2D” is a single port globe-style body with cage guiding, balanced valve plug and metal seats.


09-12-2011

Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series HPX

CVS Controls manufactures Control Valves and associated instrumentation products to specification that facilitate the direct replacement with FISHER* process control equipment. For standard cages, the flow direction is flow down with the following flow characteristics: equal percentage, modified equal percent, and linear.


09-12-2011

Manufacturing Control Valves and Associated Instrumentation Alberta, Canada - control series V

CVS Controls manufactures Control Valves and associated instrumentation products to specification that facilitate the direct replacement with FISHER* process control equipment. Typical actuators used are the pneumatic spring and diaphragm rotary actuator and the pneumatic piston rotary actuator. The flow characteristic is modified equal percent, with normal flow into the convex side of the Ball.